IEC 60331 Wire and Cable Fire Resistance and Hammer Test Machine for Fire with Shock

• Customization: Available
• Warranty: 1 Year
• Sprinkler Water Pressure: 250~350kpa
• Model NO.: GD-60331
• Timer: 0 to 9 Hours 99 Minutes 99 Seconds
• Counter Display: Small Plate Counter
• Load: 0~600V Adjustable
• Size: 1,600(W)×850(D)×1,650(H)mm
• Control Table: 600(W)×750(D)×1,200(H)mm
• Transport Package: Wooden Case
• Origin: Made in China
• HS Code: 9031809090
• Production Capacity: 100sets/Month

Product Description

IEC 60331 Wire and Cable Fire Resistance and Hammer Test Machine for Fire with Shock

Product Details

Introduction


Wire and cable fire resistance and Hammer Tester according to GB/T 19216.11-2003, GB/T 19216.21-2003, GB/T 19216.23-2003, BS 6387-2013 standard research and development production, used for flame temperature not less than 830ºC, and exert a certain impact vibration, Test instrument for line maintenance integrity. Can test cable A, B, C, D class flame retardant performance; Wires and cables that are difficult to catch fire and have the ability to prevent or delay the spread of flame usually refer to those that can pass the GB/T18380.3(equivalent to IEC60332-3) test

Product Features

Control Cabinet Parameters

1. With double flowmeter and pressure regulation.

2. Automatic control of the test process.

3. With intelligent detection function, when the sample in the test process short-circuit, automatic alarm and turn off the fire source.

4. Display: touch screen, display temperature curve

5. Time timer: 0~99 hours, 99 minutes and 99 seconds

6. Control box size: 650 (D) X400 (W) X1200 (H)

7. Load: test voltage 0~600V adjustable;

8. Load current range: 0.1 ~ 3A, the test current can be adjusted according to the standard requirements, but greater than 3A is protected;

9. The load capacity should be able to ensure that the test current close to 3A can still ensure that the test product continue to test. Also suitable for spray test and hammer test load requirements

Pounding test device pounding test device part

1. Stainless steel bracket impact structure; Box spray painting treatment:

2. Independent motor impact control box:

3. Thump cone for ⊄ thick round steel bar length of 25, 600.

4. The hammer cone is struck in free fall at an Angle of 60°.

5. Motor drive rod hammer for periodic hammer impact action.

6.Hammering cycle (time) : 10~999S (optional, standard requirements 30±2S/ time)

7. Total test time: 0~99995

8.Strip burner (same as spray test) (shared with fire-resistant combustion test stand)

9. Test temperature 600~1000° (A grade 650°, B grade 750°, C and D 10 grade 950°)

11. Temperature measuring thermocouple diameter is less than 2mm (shared with fire-resistant combustion test stand)

12. During the test, the current of each phase cable is 0.25A.

 

Spray test device (optional)
1. Adopt propane or natural gas burner, adopt integral 400mm long strip burner.
2. Combustion test temperature: 650±40°.
3. The diameter of not greater than ⊄ 2 thermocouple temperature measurement.
4. Water supply pressure of spray head: 250~350Kpa, water spraying volume of test product: about 0.25~0.3L/S.m2.
5. Test length: about 400mm.
6. During the test, the test cable is energized through the isolation transformer and connected to the 3A fuse or circuit breaker, as well as the on-off signal light indicating each phase of the cable.

 

Standard

IEC 60331	Tests for electric cables under fire conditions - Circuit integrity
IEC 60331-1&2	Part 1: Test method for fire with shock at a temperature of at least 830 °C for cables of rated voltage up to  and including 0,6/1,0 kV and with an overall diameter exceeding 20 mm
IEC 60331 part 31	Part 31: Procedures and Requirements for Fire with Shock - Cables of Rated Voltage uo to and Inculding 0,6/1 kV
BS6387-2013	Test method for resistance to fire of cables required to maintain circuit integrity under fire conditions
GB/T 19216	Tests for electric cables under fire conditions - Circuit integrity

Company Profile

Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd was established in 2009. Now, it has developed 70 kinds of fire testing instruments and served for many industries such as building materials,lithium battery, aviation, rails, IMO, wire & cable, safety protection and so on. Our mission is to provide reliable products to our customers to meet their requirements of testing, R&D and quality control. In addition, Gold insists for high-quality standard in niche markets and targets to minimize the gap between Chinese local products and imported products. We work with trust, honesty and a sense of responsibility, so the quality and service are always our advantages among all competitors.