IEC 60331 BS 6387 Wire and Cable Fire Resistance Impact Water Spray Circuit Integrity Burn Test Apparatus

• Customization: Available
• After-sales Service: Technical Support,Online Service
• Warranty: 1 Year
• Model NO.: GD-IEC 60331
• Standard: IEC 60331, BS 6387,BS 8491
• Size: 1,600 (W) * 850 (D) * 1,650 (H) mm
• Console Size: 600 (W) * 750 (D) * 1,200 (H) mm
• Power: AC 380V 3-Phase, 50 / 60Hz, 30A
• Weight: 100kg
• Flame Temperature: 600~1000c Adjustable
• Material: Stainless Steel
• Load: 0~600V Adjustable
• Timer: 0 to 9 Hours 99 Minutes 99 Seconds
• Transport Package: Wooden Box
• Trademark: GOLD
• Origin: Chongqing China(Mainland)
• Production Capacity: 100sets/Month

Product Description

IEC 60331 BS 6387 Wire and Cable Fire Resistance impact Water Spray Circuit Integrity Burn Test Apparatus

Introduction:
The wire and cable fire resistance test device is used to test the fire resistance of wiring or power grid cables. It burns in a flame of no less than 750°C and 950°C and tests the cable to maintain circuit integrity.
Wires and cables that are difficult to catch fire and have the ability to prevent or delay the spread of flames usually refer to wires and cables that can pass the GB/T18380.3 (equivalent to IEC60332-3) test.

Standard:
• IEC 60331 part 12 Testing of wires and cables under flame conditions - Shock combustion circuit integrity at least 830 degrees celsius
• IEC 60331 part 31 Procedures and requirements for impact ignition - Cables with rated voltages up to 0.6/1.0 KV
• IEC 60331-1
• BS6387-2013
- Cables subject to impact when supplying fire, flame temperature not less than 830 degrees celsius, rated voltage greater than or equal to 0.6/1kV, overall diameter exceeding 20 mm
• IEC 60331-2
- Cables that are subject to impact when supplying fire, flame temperature not less than 830 degrees celsius, rated voltage greater than or equal to 0.6/1kV, overall diameter not exceeding 20 mm
GB/T 19216
Technical Parameters:

Size	1,600(W)×850(D)×1,900(H)mm
Console Size	600(W)×750(D)×1,200(H)mm
Power	AC 380V 3-phase, 50/60Hz, 30A
Weight	300kg
Instructions	Supplied
Exhaust	Minimum 15m³/ min
Other Requirements	Vacuum cleaners, compressed gas, propane gas

Main Feature:

1. Control cabinet parameters:
* With dual flow meters and pressure regulation.
*The test process is automatically controlled.
*It has an intelligent detection function. When the sample is short-circuited during the test, *it will automatically alarm and turn off the fire source.

2. Requirements for fire resistance testing equipment:

*The burner has a nozzle 500mm long and 15mm wide. There are three rows of staggered holes on the nozzle, with a hole radius of 1.32 mm and a hole spacing of 3.2 mm. Comes with Venturi mixer;
*The test ladder frame for installing cables is fastened to the supporting steel base; during the test process, the vertical components on both sides of the test ladder can be adjusted according to different cable size requirements (test frame length: 1200mm, height: 60mm, total weight: 18±1kg)
*The inner diameter of the metal ring is approximately: 150 mm.

3. Pit test device:
*stainless steel bracket impact structure; box body spray paint treatment;
*Independent motor impact control box;
*Thick round steel rod with a hammer cone of 25 and a length of 600.
*Beat the hammering cone with an Angle of 60.
*the motor drive rod hammer for periodic hammer impact action.

Packaging & Shipping:
wooden case for IEC 60331 cable and wire fire resistance tester
Company information: