| Customization: | Available |
|---|---|
| After-sales Service: | Technical Support,Online Service |
| Warranty: | 1 Year |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
China Manufacture ISO 5660 ASTM E 1354 Flammability Analyzer Cone Calorimeter
Introduction:
The cone calorimeter is based on the oxygen consumption principle and uses the oxygen consumption principle to measure the heat release rate of the material. The so-called oxygen consumption principle is: the heat released by each unit of oxygen consumed when the material is burned is basically the same, and this value was measured to be 13.1MJ/kg±5%. In the experiment, we can load the sample on the load unit and measure the mass loss rate of the sample during the combustion process; heat the sample and Light it up through electric spark ignition to test its flammability and ignition time; collect the combustion gas in the accompanying pipe and exhaust hood, by collecting changes in flue gas pressure difference, gas concentration and temperature, and automatically test its heat release rate and other indicators; using optical devices, its smoke density performance parameters can be measured; at the same time, through the acquisition of the above data, we can obtain Extended data such as effective combustion heat and specific extinction area. Cone calorimeter testing is a safe, fast, and accurate way to inspect products. In addition to product development, cone calorimeters can also be used as quality control tools.
Standards:
ISO 5660:Tests of reaction to fire-Rates of heat release, smoke generation and mass loss
ASTM E 1354:Standard Test Method for Thermal and Visual Smoke Emission Rates of Materials
BS 476 Pt.15:Testing of building materials and building structures: - Methods for testing heat release rates of products
GB/T 16172-2007:Test method for heat release rate of building materials
NFPA 264
Applications:
Technical Specifications:
| Product Name | Laboratory Heat Release Tester Flammability Analyzer for Building Materials |
| Size | 1,800mm(W)*900mm(D)*2,650mm(H) |
| Power | 220 V AC, 50/60 Hz, 30 A |
| Weight | about 450 kg |
| Manual | Supplied |
| Exhaust | 50 l/s |
| Utilities | Compressed Air, Methane, Nitrogen, CO/CO2 Mixing Gas, Dust Collector |
Features:
1. The cone calorimeter adopts a cabinet-type design. The analysis cabinet is movable and can be used for cone calorimeter testing. It can also be connected to large-scale heat release rate testing systems such as single combustion test devices and physical room fires. And cable combustion classification testing, in line with ISO 5660, ASTM E1354, GB/T16172 and other testing standards;
2. Integrated test body and 19-inch analysis cabinet with built-in PC-type 15-inch industrial touch screen computer for the entire control and testing process;
3. The cone heater has a rated power of 5000W, a heat output of 0~100kW/m2, and is controlled by a PID temperature controller. The radiant cone can be placed horizontally or vertically;
4. The sample box can hold samples up to 100mm x 100mm x 50mm;
5. Sample weighing range: 0~2000g; accuracy: 0.1g (different ranges and accuracy can also be provided according to customer requirements);
6. The ignition system is a high-voltage spark generator of no less than 10KV, which uses a rotating cylinder to automatically position;
7. Paramagnetic oxygen analyzer, range 0-25%, response time: 4 seconds, linear deviation: ≤0.5% FS, repeatability: ≤50 ppm O2, sensitivity drift: ≤ 0.1 vol.% O2/week or ≤ 1% measured value/week (non-cumulative), whichever is smaller, detection limit: ≤50 ppm O2;
8. Non-dispersive infrared CO and CO2 analyzer CO: 0~1%; CO2: 0~10%, measurement principle: infrared absorption, response time: 2.5 seconds, linear deviation: ≤1% FS, repeatability: ≤0.5% FS, zero drift: ≤1% FS/week, detection limit: ≤0.5% FS;
9. Smoke density analysis uses a laser system to measure smoke density. The system consists of a photodiode, a helium-neon laser, a main detector and an auxiliary detector;
10. The exhaust system consists of a fan, a smoke hood, an exhaust pipe, an orifice flow meter, etc. The exhaust fan flow rate is adjustable from 0 to 50g/s, with an accuracy of 0.1g/s;
11. The annular sampler is installed in the air inlet duct 685 mm away from the smoke collecting hood. There should be 12 small holes on the sampler to homogenize the air flow components;
12. The temperature of the air flow is measured by a thermocouple installed in a closed node with a diameter of 1.6 mm. The thermocouple should be installed 100 mm above the flow measuring orifice plate;
13. Integrated gas pretreatment system, including sampling pump, filter, condenser, peristaltic pump, and moisture filter;
14. Condenser temperature: 0~5 degrees, diaphragm pump, flow rate: 3 l/min, pressure: 2.5bar;
15. Humidity alarm unit, when the moisture in the sample gas is too high, it can automatically alarm and communicate through the test software;
16. The flow alarm unit can automatically alarm when the smoke and dust in the sample gas are blocked, prompting you to replace the filter device;
17. Use the SB type heat flow meter with a design range of 0~100k W/m. The accuracy of the heat flow meter is ±3% and the repeatability is ±0.5%. A calibration report is attached;
18. Equipped with a portable water cooling system, when using the heat flow meter, the user does not need to connect to an external tap water source or equip a water pipe;
19. In order to calibrate the response of the entire test system, a methane calibration burner is used to measure the C-coefficient value;
20. The data acquisition system can automatically record the output of gas analyzers, orifice flow, thermocouples and other instruments;
21. Equipped with a software operating system, the test results include: heat release rate, flue gas flow rate, C coefficient, sample ignition time and extinction time, total oxygen consumption, total smoke generation, mass loss rate, total heat release, Effective combustion heat, carbon dioxide production and carbon monoxide production.
Packing & Delivery:
To better ensure the safety of your goods, professional, environmentally friendly, convenient and efficient packaging services will be provided.
About Us:Since 2008, Gold has developed 70 kinds of fire testing instruments and served for many industries such as building materials, aviation, rails, IMO,wire & cable, safety protection and so on.
Our mission is to provide reliable products to our customers to meet their requirements of testing, R&D and quality control. In addition, Gold insists for high-quality standard in niche markets and targets to minimize the gap between Chinese local products and imported products.
We work with trust, honesty and a sense of responsibility, so the quality and service are always our advantages among all competitors.
FAQ:
1. who are we?
We are based in Chongqing, China, start from 2009,sell to Domestic Market(30.00%),Mid East(20.00%),Africa(15.00%),Southeast Asia(10.00%),Western Europe(5.00%),Eastern Asia(5.00%),Eastern Europe(5.00%),South America(5.00%),North America(5.00%). There are total about 51-100 people in our office.
2. how can we guarantee quality?
Always a pre-production sample before mass production;
Always final Inspection before shipment;
3.what can you buy from us?
Petroleum Testing Equipment,Petroleum Laboratory Equipment,Asphalt Testing Equipment,Bituminous Mixture Testing Equipment,Road Lab Equipment
4. why should you buy from us not from other suppliers?
As a leading manufacturer of Petroleum Testing Equipment and Road Lab Equipment in China, we've engaged in the field for 20 years, with rich experience in related projects. Client, Quality and Service are always our supreme target!
5. what services can we provide?
Accepted Delivery Terms: FOB,CFR,CIF,EXW,CIP,CPT,DDP,DDU,DAF;
Accepted Payment Currency:USD,EUR,JPY,CAD,AUD,HKD,GBP,CNY,CHF;
Accepted Payment Type: T/T,L/C,D/P D/A,MoneyGram,Credit Card,PayPal,Western Union,Cash,Escrow;
Language Spoken:English,Chinese,Spanish,Portuguese,German
){kind=link}